COMBINED HEAT AND POWER GENERATION UNITS
The services and engineering equipment we deliver, install, operate, maintain ...
operating on the principle of piston combustion engines (driven by natural gas, biogas, degassed coal mine methane (CMM)), along with all the necessary accessories.
Most of the CHP units offfered by TENERGO Brno, a.s., are the product of one of the company´s shareholders, the company TEDOM, s.r.o., which addresses the combined heat and power units since its foundation. Currently the firm mentioned latter belongs to one of the most significant manufacturers of small and medium scale CHP units of outputs ranging from 5 kWel to 2 MWel (power output of one single unit). Until present times more than 1.300 CHP units produced by TEDOM have been installed worldwide. Optionally, we are able to deliver also CHP units made by other renowned manufacturers. The range of power outputs of the units we are capable to deliver reaches up to 20 MW, driven by the following fuels: natural gas, biogas (agriculture, WWTPs, domestic waste dumps), degassed CMM, coke oven gas, light or heavy fuel oils and other types of fuels (non-standardized fuels necessitate to pass through an analysis, in advance). On request we also can offer power units installed in containers, equipped in accordance with the client´s requirements (temperature, humidity, noise level etc.).
In addition to the large scale of different fuels we also can offer CHP units for nearly all modes of power supply, such as the copying of own consumption schemes, power deliveries to the mains, unit island operation, operation as an energency power source, and a combination of these operation modes
BIOMASS AND BIOMASS FIRED BOILERS
(woodchips, straw, non-contaminated wooden waste, maize), including fuel reservoirs and fuel depots, fuel transport ways and all other accessories.
We use the experience gathered by our staff during the implementation of such technologies into our own power generation plants. Based on the request we obtain we are ready to offer optimum engineering solution to the client´s system, depending on the type of fuel available, the space arrangement, the power output and other important attributes
WARM WATER, HOT WATER AND STEAM BOILERS
Warm water, hot water and steam boilers with a full-scale equipment.
We are able to provide the client with any concept of performance (output, pressure, amount...). On request we can also supply units installed in containers, equipped in accordance with the requirements (temperature, humidity, noise level etc.).
SOLID FUEL BOILERS
(wood, coal) – in this commodity we offer also fully automatic boilers.
EXCHANGER STATIONS
(junction exchange station and house heat exchanger stations – of any type and scope of output power).
We manufacture and supply exchanger stations or house block stations in line with the customer requirement, arranged both as self-contained blocks for heating purposes, heatup of DHW, or a combination of the both. The circuit diagrams of the individual blocks are either of our own origin or those submitted by designers of the contractor. The general attributes that distinguish the system are its mobility, compactness, reduced space requirements, attendance-free operation with connections established to the central room, quick and easy assembly, and easy cleaning of the demountable exchanger for the heatup of DHW (we also make cleaning works on heat exchangers not intended for disassembly). The valves and fixtures used by us meet all the operational requirements of the system, in particular as regards the safety and quality.
HEAT PIPELINES
We install pipelines for warm and hot water (preinsulated conduits for indoor and outdoor installation), including the groundworks.
AIR CONDITIONING UNITS
Systems with power generation units, refrigeration units (compressor stations, absorption units), as well as ventilation equipment – ventilators (installed in pipelines, wall or roof-mounted), components of the air conditioning system (filters, shutters, valves, heaters, dampers and louvers), air locks (for mounting in doors, gates, suspended ceilings), distribution elements (outlets, fuses, anemostats, dish valves), air conduits and channels (piping, flexible hoses, shaped pieces and accessories), control units (governors) and ventilation units (according to the requirement).
All equipment for boiler houses, heat generation plants, hotels, hospitals, department stores, sporting facilities...
HEAT PUMPS
(air-water, water-water, ground-water), with accessories. Installation of heating system devices into family-houses and apartment dwelling houses. Technological applications – utilization of the waste heat and further applications.
MEASUREMENT, REGULATION, ELECTRICAL ENGINEERING ASSEMBLY WORKS
- Deliveries of components (building automation, heating, air conditioning). In co-operation with another renowned manufacturers we are able to deliver technologically open and arbitrarily structured systems.
- Installation works on heavy-current equipment operating at all voltage levels
- Electrical assembly works (energy centres, business centres, hotels, health centres, hospitals, schools, industrial buildings)
CIVIL ENGINEERING ACTIVITIES
During the long-year periods of the installation of power supply equipment into most variable environments we all the time had to face and were involved in ancillary construction works and civil engineering works in general. The result of our comprehensive marketing, along with the assessment of our capabilities, in combination with the engineering components available on the market and a long-term co-operation with a design bureau is our comprehensive offer of civil engineering activities, with special focus on shops of all kind, warehouses, buildings for the installation of power centres, combined projects for installation into buildings and containers, and modifications to dwelling spaces. All this in ready-to-use arrangement, with taking all the specificity of the individual customer into consideration.